Wooden Slot In Fence Posts
Western Post & Rail. Posts are drilled 16″ on center to accept rails and have domed tops. Fence rails are 8′ in length and available in a 4″ Uniform Diameter, doweled to 2″ diameter to fit in posts. Give your estate this rustic and attractive fencing and enjoy years of the best looking wooden ranch fence available. The Fastest (and Most Foolproof) Way to Install Fence Posts For fence posts that are firmly set and straight, all you need is a good technique, a helpful friend, and the right products. Clamp the fence in place, slide the blank to the mark at the other end of the slot and check that it’s aligned properly. Put a mark on the edge of the board that’s against the fence. Keep this edge against the fence when you flip the board over and drill the other side. This ensures the holes are in line even if your a hair off centre of. Shop great deals on Wooden Fence Posts. Get outdoors for some landscaping or spruce up your garden! Shop a huge online selection at eBay.com. Fast & Free shipping on many items! Wood Fencing and Wood Fence Posts. The most cost effective means of keeping in what you want kept in and out what you need to keep out is properly pressure treated wood products. Wood fence posts have been used for years as the most effective means of fencing.
There are two common basic methods of constructing rails for board fencing, the easiest method is to have the rails on the front of the posts then fitting the boarding along the whole length. The alternative method is to fit the rails between the posts (with their front faces about 25 mm back from the front of the posts, and then fix the boards between the posts.
The rails
Two types of rails are commonly found - arris rails with a triangular cross-section, and cant rails which are more or less rectangular with the top edge sawn at an angle to allow rainwater to run off away from the fence boards.
Traditionally arris rails had tongues cut at their ends which fitted into slots cut in the posts. The tongues took the full weight of the forces on the fence, so they often broke after a time.
Galvanised steel repair brackets, which are available in a number of designs to suit both arris and cant rails could be used to repair broken rails as necessary. These repair bracket can be used when constructing a new fence, they avoid having to spend a lot of time cutting the tongues and slots.
Unless the boards are going to be fitted between the posts, it is simpler to use cant rails (with their vertical back edge) and fix them across the front of the fence posts.
Concrete posts can be used and the cant rails secured to the posts by bolts with their heads recessed into the rails using suitable holes though the posts, or special posts are available to take metal brackets to suit the type of rail being used.
In general, rails should be positioned no greater than about 200 mm (8 inches) down from the top of the boards or up from the bottom. Vertical spacing between rails should be no greater than about 700 mm (28 inches). This allows for a fence up to about 1.1 m (43 inch) to be built with just two rails, while fences over that should have 3 rails with the middle rails equally spaced vertically between the upper and lower rails.
Erecting the posts and rails
The traditional slotted arris rails.
If the posts being used do have have slots already cut to accept the trimmed arris rails, the first job is to cut the slots. The slots can be simply made by drilling three, overlapping holes all the way through the posts using a 20mm (7/8in) flat bit in an electric drill. To clean up the holes, use a chisel to remove the surplus wood in the slot.
The ends of the arris rails should be trimmed using a saw and finished off with a file so they are a snug fit in the post slots.
Before assembly, paint the slots and ends of the rails with wood preservative. Start by erecting one end post ensuring that it is vertical. Stretch a string line along the proposed run of the fence to the end of the fence run to ensure that subsequent posts are in line.
Set out the intermediate posts, try to keep them equally spaced with no more than 3m (10ft) between each pair. Dig a hole for the second post and push the ends of each arris rails into the slots in the first two posts.
Use timber struts to temporarily hold the posts upright, and check with a spirit level that the rails are horizontal (unless the ground is on a slope in which case, check that the rails are in the line of the general slope). If necessary dig the hole deeper, or pack it up with broken bricks, to get the post at the correct level.
Continue in this manner with the third and subsequent posts until all the posts and rails have been completed. If it is impossible to move the last post sufficiently to allow the rails to be fitted in the slots, the last rails can be sawn off square and attached to this last post using galvanised rail repair brackets.
With all the posts inserted and temporarily strutted, hard-core can be rammed around each (ensure that each remains vertical) and fixed permanently using concrete (see fence posts) at soil level. When the concrete has hardened, go along the posts and drive a nail, at an angle, in the front of each post to secure the tongue of each rail in the post slot.
Using cant rails on the front face of the fence posts.
Wooden Slot In Fence Posts At Home Depot
Erect the posts as described above at no more than 3m (10ft) spacing and secure them using concrete.
Wooden Slot In Fence Posts Post
When the concrete has hardened, the cant rails can be fixed to the front face of each pair of posts. The rails can be fixed either in line with the next, or staggered. By staggering then, a stronger fixing may be achieved as the nails are not so near the ends of the rails as the other joints.